Email:[email protected]

precision ball bearing oil restrictor

Just fill in the form below, click submit, you will get the price list, and we will contact you within one working day. Please also feel free to contact us via email or phone. (* is required).

  • Precision Oil Restrictor (-4AN) for Garrett Ball Bearing ...


    Precision Turbo's Oil Feed Restrictor fitting with -4 AN Male Flare x 7/16-24 thread and a 0.035' orifice. This thread is designed to thread directly into Garrett Turbos. Turbo oil restrictors are often a necessity for ball bearing turbos to restrict the flow and pressure of the oil reaching the CHRA. By reducing this excess windage on the bearing you can achieve optimal boost response ...

    Get Price
  • Precision Turbo Oil Feed Restrictor for Garrett Ball ...

    2015-5-6 · Precision also told me it wasn't required but I had smoking issues. My engine builder (Accufab) told me these motors have to much oil pressure for Precision's restrictor and told me to restrict it down further. Hellion turbo recommends having 4.5 ounces of oil drain in a 30 second time frame. So basically you'd do this test and jet accordingly.

    Get Price
  • precision 7675 ball bearing oil restrictor ...

    2020-4-22 · Precision claims the oiling hole in the cage pin acts as enough of a restrictor that you do not need to double-stack a restrictor in the line as you may with a Garrett GT unit; they also want the turbo to pass more oil to suppress heat in the cartridge due to the lack of coolant ports on the outer bearing …

    Get Price
  • Does my ball bearing Precision PT-series turbo need

    2015-8-25 · If You Have a Garrett GT25r, GT28r, GT30r, GT35r series Turbocharger, then You Need a Garrett Ball Bearing Oil Restrictor. This Oil Restrictor Fits Directly into the Ball Bearing Cartridge, and Seals on the Ball Bearing Cage Dowel Pin. This Fitting Has a -4 an Connection fitting to Adapt Directly To a -4 an Oil Feed line.

    Get Price
  • Garrett Ball Bearing Oil Restrictor - Turbo Lab

    0.03' oil restrictor bolt for the turbo side. Intended for all GT or T-series ball bearing turbo chargers. Ball bearing turbos require use of the restrictor bolt to avoid over-pressuring the turbo oil seals.

    Get Price
  • Ball Bearing Oil Restrictor - GenRacer

    2010-5-11 · hi I have 6262 turbo form precision. it is journal (not ball bearing). Should I use any oil restrictor on it? I do research and some say use, some do not use. My oil suply line us 4AN. I have one restrictor about 1,5 mm (about 1/16 inch) and do not know use it or not. what is your experience...

    Get Price
  • Precision 6262 (journal): oil restrictor or not? | Supra ...

    2018-9-29 · I did some quick and dirty data comparison after installing a 0.035' oil restrictor on my gen2 PTE 6266 ball bearing turbo. I went with a restrictor because after double checking the drain and PCV setup, the turbo still burned oil with occasional smoke on hard pulls when hitting high rpms.

    Get Price
  • Technical - PTE oil restrictor before/after | SpoolStreet ...

    2014-4-16 · 2. Turbocharger oil feed line sizes. (BALL BEARING) The oil feed to ball bearing turbochargers may be restricted but may not always be necessary. If a ball bearing turbocharger is supplied with an oil feed restrictor fitting it is suggested that this fitting be utilized. All single ball bearing turbocharger applications should utilize -4AN or 1/4

    Get Price
  • Turbocharger Install Recommendations - Precision Turbo

    2021-5-21 · Oil pressure entering a ball-bearing turbocharger needs to be between 40 psi and 45 psi at the maximum engine operating speed. For many common passenger vehicle engines, this generally translates into a restrictor with a minimum of 0.040' diameter orifice upstream of the oil inlet on the turbocharger center section.

    Get Price
  • Precision Turbo Oil Feed Restrictor for Garrett Ball ...

    Precision Turbo's Oil Feed Restrictor fitting with -4 AN Male Flare x 7/16-24 thread and a 0.035' orifice. This thread is designed to thread directly into Garrett Turbos. Turbo oil restrictors are often a necessity for ball bearing turbos to restrict the flow and pressure of the oil reaching the CHRA.

    Get Price
  • Treadstone Performance Inc., Turbo Kits, Intercoolers ...

    Oil Inlet Restrictor, Journal bearing Garrett, Precision & Turbonetics. Oil inlet restrictor for T series turbos. 1/8' NPT Oil inlet restrictor for all T3, T3/T4, T04, T72 etc. Also larger ball bearing turbos such as GT4088R, GT4094R, GT4294R, GT4202R.

    Get Price
  • Amazon.com: turbo oil restrictor

    4AN Turbo Oil Feed Restrictor Fitting AN4 To 7/16-24 Copper Fitting adaptor for GT25 GT25R GT28 GT28R GT35 GT35R T25 Turbocharger Ball Bearing Turb 13.99 13 . 99 5% coupon applied at checkout Save 5% with coupon

    Get Price
  • Precision 7675 Oil Issues- Advice Welcome ...

    2015-3-3 · The .038' restrictors were for ball bearing turbos. When I had Precision repair the screwed up turbo I upgraded both turbos to dual ball bearing and just to be safe I went a little bigger on the restrictor size (.058'). I actually need to jet it down a hair but I want to measure the oil …

    Get Price
  • Introducing the SPE S300 Ball Bearing Turbocharger ...

    2020-8-28 · REDUCED OIL FLOW. The ball bearing design reduces the required amount of oil to provide adequate lubrication. On most ball bearing turbochargers an oil restrictor must be run in the oil line/turbo oil inlet. We have machined the center cartridge in a way that there is no need for a restrictor. This allows for the turbo to have optimum ...

    Get Price
  • Study of membrane restrictors in hydrostatic bearing

    Bearing body: 11, this part uses the oil cavity pressure after throttling, uses the effective area that bearing holds itself, and supports the weight of bearing itself.

    Get Price
  • PULSAR G25-550 Dual Ball Bearing Turbo – Pulsar

    Home Universal Turbos G Series Turbos PULSAR G25-550 Dual Ball Bearing Turbo. PULSAR G25-550 Dual Ball Bearing Turbo ... -4AN to the Oil Restrictor; Oil Drain: Std T3 Oil Drain Flange; Additional information. Compressor Housing Options: ... Ball Bearing Cartridge for Garrett GT37R Precision 5031E 6262 6266 GEN 1 Turbos 502337001 149.99 ...

    Get Price
  • oil feed on Precision turbo 6266 2jzgte | Supra Forums

    2014-5-1 · I live in saudi and i couldnt find braided lines with -3 size. I only found -4 and I know that the recommended on a 2jzgte on a journal bearing Precision 6266 turbo is -3. I can add a restrictor to the -4 oil line but i don't know what size to get. I need some recommendations for my setup. Is...

    Get Price
  • What Causes a Turbo To Blow, Leak, or Burn Oil? Find

    2014-12-20 · Ball Bearing Turbos Need a .035” Restrictor However, Because their Cartridges Are Much Smaller, and They Can only Hold So Much Volume. Oil Restrictor in a Journal Bearing Turbo . Having and Oil Restrictor in a Journal Bearing Turbo can Causes Turbos to Eventually to Blow oil, Because it Starves the Turbo Of Oil, Which Causes the Internals of ...

    Get Price
  • Precision Turbo and Engine: Turbochargers, Air/Fuel ...

    2018-12-5 · Precision Turbo & Engine is a leader in turbocharger technology for street and race applications. Precision offers a full line of custom turbochargers, accessories, intercoolers, fuel injectors and stand alone engine management systems.

    Get Price
  • Precision Turbo Oil Restrictor (-4AN) f Ball Bearing ...

    Precision Turbo Oil Restrictor (-4AN) f Ball Bearing turbos 074-2018 Product Code: PTB-074-2018

    Get Price
  • GT 0.060' Oil Flow Restrictor • Full Race

    The precision machined orifice with in this restrictor precisely controls oil flow to the turbocharger. We highly recommend monitoring oil pressure prior to installing a restrictor. We also recommend monitoring pressure after the restrictor is installed. Oil Restrictor Specifications:-4 Oil inlet fitting for GT Ball Bearing turbos; For GT28 ...

    Get Price
  • 4AN to 1/8NPT 1.0mm Restrictor Turbo Oil Feed

    MAMBA -4AN to 1/8NPT Straight Turbo Oil Feed Adapter Fitting (1.0mm Restrictor) Product. Situation. Brand New in Box. Application. Precision Ball Bearing Turbo: Material. JIS3771 Brass. Kit Includes. 1 x Adapter Fitting. Made By. MAMBATEK. Warranty. One Year

    Get Price
  • Oil Inlet Restrictor - .065' hole size 1/8' NPT (for ...

    Oil inlet restrictor for all T3, T3/T4, T04, T72 etc. turbos (also larger ball bearing turbos such as GT4088R, GT4094R, GT4294R, GT4202R). Restrictor diameter of .065 hole size. Installed at the oil inlet on turbo to reduce max oil pressure going into the turbo to prevent oil …

    Get Price
  • 7/16-24 IF AGP/Garrett Twin Ball Bearing to -4 Oil

    This fitting screws into the bearing housing of AGP/Garrett T Series Twin Ball Bearing turbos. It has the properly sized oil restrictor built in. The threads are 7/16-24 Inverted Flare NOTE: THIS IS NOT INTENTED TO BE USED AS AN OIL RESTRICTOR FOR STANDARD BEARING TURBOS.

    Get Price
  • Study of membrane restrictors in hydrostatic bearing

    Bearing body: 11, this part uses the oil cavity pressure after throttling, uses the effective area that bearing holds itself, and supports the weight of bearing itself.

    Get Price
  • Turbo System Optimization - Garrett Motion

    2021-5-18 · Ball Bearing Turbo. An oil restrictor is recommended for optimal performance with ball bearing turbochargers. Oil pressure of 40 – 45 psi at maximum engine speed is recommended to prevent damage to the turbocharger’s internals. In order to achieve this pressure, a restrictor with a 0.040” orifice will normally suffice, but you should ...

    Get Price
  • Study of membrane restrictors in hydrostatic bearing

    2018-9-10 · Restrictor valve: 10, restrictor adjusting element between the shaft and the oil supply system between the pressure pads; the hydrostatic bearing has the ability to compensate the load change. 3. Bearing body : 11, this part uses the oil cavity pressure after throttling, uses the effective area that bearing holds itself, and supports the weight ...

    Get Price
  • MAMBA Turbo Oil Water Line 1.8T Transverse VW

    BorgWarner EFR Ball Bearing turbo. BorgWarner K03/K04 Journal Bearing Turbo. Precision PTE Ball Bearing Turbo. Kit Includes. 1 x 70cm PTFE Braided Stainless Steel Teflone line. 1 x 4AN Adapter fitting Kit to turbo oil feed (1.0mm restrictor to Ball Bearing Turbo/2.5mm restrictor to Journal bearing turbo) 1 x 1/8NPT Tee (To oil pressure switch)

    Get Price
  • Electric Oil Feed and Scavenge Pumps - RB Racing-RSR

    2021-3-11 · Reduces line pressure by 25 psi. Used where line pressure is too high for both plain bearing and ball bearing turbochargers. On very high pressure systems with ball bearing turbochargers these can be used in conjunction with an oil restrictor fitting on the turbo inlet. If idle oil pressure is 45 psi then 20 psi will be the turbo feed pressure.

    Get Price
  • Precision Turbo Oil Restrictor (-4AN) f Ball Bearing ...

    Precision Turbo Oil Restrictor (-4AN) f Ball Bearing turbos 074-2018 Product Code: PTB-074-2018

    Get Price
  • JPC- Ball Bearing Turbo Oil Restrictor - Justin's ...

    JPC- Ball Bearing Turbo Oil Restrictor. 22.99 ) No reviews yet Write a ... This includes GT25-GT35 turbochargers and some of Precision's earlier water cooled units. If you have a Garrett CHRA that has water cooling fittings, this oil inlet fitting must be used. Precision part # 074-2018, for use with -4AN oil …

    Get Price
  • Precision Turbo Oil Feed Restrictor Fitting for Garrett ...

    2020-6-17 · Precision Turbo's Oil Feed Flange Kits include everything needs to fit your oil feed line up to the turbo. These turbo feed flange kit are available for small frame and mid/large frame turbos including the GT40R, GT42R, GT45R, GT55, GT60, PT91 thru PT114. Dimension will vary accordingly.

    Get Price
  • Precision Turbo Accessories - No Limit Motorsport

    Bearing Housing Flange Kits (Oil Inlet) 074-2020: Bearing Housing Flange Kit for GT32, GT35, GT37 and GT40 non ball bearing turbos (includes oil feed fitting, oil feed flange, bolts, and gasket) 074-2023: Bearing Housing Flange Kit for GT40R, GT42R & GT45R (includes oil feed flange w built-in -4AN oil restrictor, bolts, and gasket) 074-2026

    Get Price
  • Introducing the SPE S300 Ball Bearing Turbocharger ...

    2020-8-28 · REDUCED OIL FLOW. The ball bearing design reduces the required amount of oil to provide adequate lubrication. On most ball bearing turbochargers an oil restrictor must be run in the oil line/turbo oil inlet. We have machined the center cartridge in a way that there is no need for a restrictor. This allows for the turbo to have optimum ...

    Get Price
  • Hydrostatic Bearings with Self-Controlled Restrictors ...

    In this research, a compact headstock using hydrostatic bearing with a self-controlled restrictor is proposed. Numerical analysis of dynamic stiffness and static stiffness of the proposed bearing is carried out by using Reynolds equation, which considers non-linearity of oil flow at restrictor, elastic deformation of plumbing and volumetric ...

    Get Price
  • G-Series G57-2000 88mm - Most Advanced Large

    2021-5-18 · An oil restrictor is recommended for optimal performance with ball bearing turbochargers.The G57 turbochargers utilize a massive 16mm dual ball bearing cartridge with steel cages. An oil pressure of 40 – 45 psi at maximum engine speed is recommended to prevent damage to …

    Get Price
  • MAMBA Turbo Oil Water Line 1.8T Transverse VW

    BorgWarner EFR Ball Bearing turbo. BorgWarner K03/K04 Journal Bearing Turbo. Precision PTE Ball Bearing Turbo. Kit Includes. 1 x 70cm PTFE Braided Stainless Steel Teflone line. 1 x 4AN Adapter fitting Kit to turbo oil feed (1.0mm restrictor to Ball Bearing Turbo/2.5mm restrictor to Journal bearing turbo) 1 x 1/8NPT Tee (To oil pressure switch)

    Get Price
  • PROS and CONS of Ball Bearing Turbochargers - Pro

    2018-9-10 · Journal bearing designs not only use big volumes of oil to float the components, this same large volume of oil cools the components so you have a cooler running turbo as well. So the next time someone tells you, its got ball bearing turbos… or you have the option to choose between ball bearing or Journal turbos… weigh the pros and cons.

    Get Price
  • PTE Leaking From Top Feed Connection | SpoolStreet

    2019-1-8 · Been running a 0.035' restrictor for 5k miles 4 months and the turbo hasn't lunched itself yet. N54s and other engines with high oil pressure do benefit from a restrictor for ball bearing turbos only if you have oil consumption at high rpm high load, and everything else checks out.

    Get Price
  • JPC- Ball Bearing Turbo Oil Restrictor - Justin's ...

    JPC- Ball Bearing Turbo Oil Restrictor. 22.99 ) No reviews yet Write a ... This includes GT25-GT35 turbochargers and some of Precision's earlier water cooled units. If you have a Garrett CHRA that has water cooling fittings, this oil inlet fitting must be used. Precision part # 074-2018, for use with -4AN oil …

    Get Price
  • 1G - restricter on presision turbo | DSMtuners

    2020-8-8 · thank you all for the info guys. i have looked over the install recomendations and it says nothing of the ball bearing turbo and restrictors. i also have contacted presision twice but they havnt answered me. the turbo is new and does look to have a restrictor screwed i to the oil feed but i just dont know if its enough. and with precision not answering i thought maybe someone on here may have ...

    Get Price
  • EXTREME PSI : Your #1 Source for In Stock

    2021-5-21 · These oil restrictors are available in 0.020', 0.030'' or 0.040'' for your ball bearing turbos, or as a straight non-restricted fitting for journal bearing turbos. Garrett GT ball bearing turbos like lower oil pressure and sometimes the built in restrictor is not enough. With these -04 AN oil feed line fittings you can ensure your GT Ball ...

    Get Price
  • Adjustable restrictor systems | SKF Lincoln | SKF

    242 series systems make use of adjustable restrictor valves to feed specified individual oil flows to each lubrication point. They come with adjustment screws and sight glasses for visual check of the oil flows. Three different screw in sizes on connecting bars range from oil flows as low as 0.01 to 2.0 l/min. and viscosities of up to 1000 mm²/s.

    Get Price
  • 7/16-24 IF T2 GTBB Ball Bearing to -4 Oil Feed Fitting ...

    This fitting screws into the bearing housings of T2, GT25R, and GT30R/GT35R Ball Bearing turbochargers from Garrett. It has a -4 fitting on the other end to connect to your oil feed line. GT Ball Bearing turbos have internal oil restrictors so adding one externally is not recommended.

    Get Price
  • Precision Turbo Accessories - No Limit Motorsport

    Bearing Housing Flange Kits (Oil Inlet) 074-2020: Bearing Housing Flange Kit for GT32, GT35, GT37 and GT40 non ball bearing turbos (includes oil feed fitting, oil feed flange, bolts, and gasket) 074-2023: Bearing Housing Flange Kit for GT40R, GT42R & GT45R (includes oil feed flange w built-in -4AN oil restrictor, bolts, and gasket) 074-2026

    Get Price
  • Precision Turbocharger PT6466 CEA (Ball Bearing)

    Precision GEN2 PT6466 CEA (Ball Bearing) HP Rating: 900. One of our most highly-anticipated turbochargers, the 6466 is capable of producing unparalleled power in a relatively compact package. Combined with Precision's exclusive CEA® compressor and CEA® turbine wheel technology, the 6466 packs is one of the most potent turbochargers available.

    Get Price
  • On 3 Performance 67mm Ceramic Ball Bearing

    The ceramic BB line of On 3 Performance Turbochargers will require the oil feed restrictor. So if you are purchasing this, be sure to also add that item to your cart when checking out. You will chance damaging the turbocharger if you do not restrict the ball bearing units

    Get Price
  • PROS and CONS of Ball Bearing Turbochargers - Pro

    2018-9-10 · Journal bearing designs not only use big volumes of oil to float the components, this same large volume of oil cools the components so you have a cooler running turbo as well. So the next time someone tells you, its got ball bearing turbos… or you have the option to choose between ball bearing or Journal turbos… weigh the pros and cons.

    Get Price
  • Garrett - Advancing Motion - G57-1950 | Facebook

    An oil restrictor is recommended for optimal performance with ball bearing turbochargers.The G57 turbochargers utilize a massive 16mm dual ball bearing cartridge with steel cages. An oil pressure of 40 – 45 psi at maximum engine speed is recommended to prevent damage to the turbocharger’s internals.

    Get Price